If it can be modified, it should.
Interface Overview Detailed Feature Descriptions 1. Speed Altitude Tapes The tapes are dynamic vertical scales. 2. Navigation Display (Active Flight Plan) When a navigation is active, the following elements appear: 3. Connection Safety Alerts 4. Hardware Monitoring Alerts and Notifications The system provides both audible and visual alerts. The list below describes each Continue reading MAVLinkPFD…
Last Updated: March 17, 2026 1. Overview MAVLinkPFD (the App ) is designed to function as a Primary Flight Display using the MAVLink protocol. We value your privacy and believe that your flight data belongs to you. This policy explains our stance on data collection and privacy. 2. Information Collection and Use MAVLinkPFD does not collect, Continue reading Privacy Policy for MAVLinkPFD
he Chinese brand Kingdunalarm has produced the LM-101LG for years. These detectors have been imported into the EU since at least 2013, often marketed under names like No-Flame and Nor-Tec. It is a reliable, linked optical smoke and heat detector, making it a good candidate for this modification. This modification adds Zigbee compatibility, allowing you Continue reading Adding Zigbee to a common…
THIS PRODUCT IS ONLY AVAILABLE THRU https://jonbrotherton.fws.store/product/bmsone-v2-plug-and-play Description: This device is not limited to 3DR Solo, but build to work with any 2S-6S battery and ArduPilot. Provides a realistic state of charge and individual cell voltages. 3DR Solo can use any Li-xx battery in 4S to 5S configuration. (The Solo gimbal is not compatible with Continue reading…
3DR Solo, have a great onboard computer, the IMX6 runs Yocto Linux : link to the Linux source: https://github.com/OpenSolo/imx6-linux Among it s best features is the HDMI-in, USB, and mini-PCIe port which can easily use rather powerful MicroTik router/Wi-Fi modules. I reverse-engineered the remaining pins, as only the 3 and 6 pin headers were known to Continue reading 3DR Solo iMX6 as video and…
Users of BMSOne can find it hard to remove the special Solo battery connector from a dead battery, this is a guide on how to do it, with a focus on simplicity. No desoldering vacuum station, preheater, or reflow oven required. 🙂Or: you can just buy it here (somebody else is selling, I am just Continue reading Simple desoldering of the Solo Battery Connector
This product is discontinued. Version2 is here: https://madhacker.org/bmsone-2-universal-2s-6s-bms-for-ardupilot/ This BMS is very flexible and universal, you can fly any 4-cell battery chemistry/capacity that the Solo can handle in terms of voltage weight, anything that produces 10-20v(I did not actually research/test Solo s upper voltage limit) The PCB is less than 50x40x9mm (the balancing…
FLIR ONE is a nice product, with an extremely limiting battery and bad software. (Luckily, third-party software is much better) You may say the battery has two reasons to be there:1: Limit useful time: pushing users to a more expensive product.2: Obsolescence by design: become useless as the battery age and stops working. Goals:1: remove Continue reading FLIR One: USB-C and battery mod.
Latest progress: See https://madhacker.org/bmsone/ the resulting product. 13 January 2020: It s working as expected. (The balancing connector header had 2mm pitch on PCB (my bad), therefore, this test version got a wire.) All Calibration/setup/programming and firmware updates are done over the FTDI header. Please do not think much about the poor flight time I Continue reading Solo/Ardupilot SMBUS…
This laser driver board seems to be common for many 20W LED lasers used for cutting/engraving. Whenever powered on, it defaults to full power due to a rather strong internal pull-up. Most CNC machines have a laser TTL PWM output that goes into high-impedance mode on boot. In that case, any connection to, or reboot Continue reading SW-LD73 Laser driver modification.