104 lines (94 with data), 5.1 kB
#
# this config file was automatically generated
# using lirc-0.8.1-CVS-pvr150(udp) on Fri Apr 6 17:00:41 2007
#
# contributed by John Lofgren
#
# brand: Zenith
# model no. of remote control: ZN5015
# The ZN5015 is a universal remote. This config file is setup using code 838 -
# one of the two listed Tivo remote codes. After trying a few codes, this code
# worked with the most buttons on the remotes and gave few redundancies in the
# key codes. Note the
# devices being controlled by this remote: mythtv frontend/backend
#
# NOTES:
# The ZN5015 is a cheap universal remote. This config file is set up using code
# 838 - one of the two listed Tivo remote codes. After trying a few codes, this
# code worked with the most buttons on the remote and gave few redundancies in
# the key codes. Note the following:
# -To set the remote code:
# 1. Hold down CODE SEARCH for a couple seconds until the LED stays on.
# 2. Press one of the four source device buttons: VCR, SAT, CBL, or DVD.
# (Do not choose TV - this button can only be used for TV codes.)
# Note, you can set a different code for each of the source buttons.
# 3. Type in the three digit code (8, 3, 8). The LED should turn off if
# you were successful.
# -The SHIFT key is not very friendly. It is a pain-in-the-you-know-what. But,
# as they say, it is best to know thy enemy. The SHIFT key is used to activate
# the green-colored functions on several keys
# When SHIFT is pressed once, the LED turns on. Press it again to turn SHIFT
# off. When SHIFT is on, the code for
# the green function of the button will be output. When SHIFT is off, the
# code for the other function on the key will be sent. For example, when you
# press the UP / CHAN+ key, if SHIFT is on, the code for UP will be sent. If
# SHIFT is off, the code for CHAN+ will be sent. Make sure SHIFT is off when
# pressing buttons without a green function. These buttons may produce no code
# or a code for a different button while SHIFT is on.
# -The following keys control the remote itself and are not meant to output IR
# codes: TV, VCR, SAT, CBL, DVD, CODE SEARCH, SLEEP, SHIFT
# -The volume up, down, and mute keys do not work with code 838.
# -The GUIDE and INFO keys produce the same output with code 838.
# -The PREV CHAN/REPEAT and ENT(er) keys produce the same output with code 838.
# -The CC (closed caption)/SUBTITLE and INPUT/TV-VCR keys produce the same
# output with code 838.
#
begin remote
name Zenith_ZN5015_CODE838
bits 12
flags SPACE_ENC
eps 30
aeps 100
header 2478 503
one 1278 501
zero 666 501
post_data_bits 8
post_data 0x59
gap 13260
min_repeat 2
toggle_bit 0
begin codes
KEY_POWER 0xA8B # Was: power
KEY_CHANNELUP 0x08B # Was: chan_up
KEY_CHANNELDOWN 0x88B # Was: chan_down
KEY_UP 0xFAB # Was: up
KEY_DOWN 0x06B # Was: down
KEY_LEFT 0x46B # Was: left
KEY_RIGHT 0x86B # Was: right
KEY_OK 0x7AB # Was: ok
KEY_MENU 0xF6B # Was: menu
KEY_QUIT 0xC6B # Was: quit
KEY_EPG 0xD4B # Was: info
KEY_INFO 0xD4B # Was: guide, duplicate
KEY_CLOSE 0xCEB # Was: closed_caption
# prev_chan 0xD0B
KEY_1 0x00B # Was: one
KEY_2 0x80B # Was: two
KEY_3 0x40B # Was: three
KEY_4 0xC0B # Was: four
KEY_5 0x20B # Was: five
KEY_6 0xA0B # Was: six
KEY_7 0x60B # Was: seven
KEY_8 0xE0B # Was: eight
KEY_9 0x10B # Was: nine
KEY_0 0x90B # Was: zero
KEY_ENTER 0xD0B # Was: enter
# input 0xCEB
KEY_REWIND 0xD8B # Was: rew
KEY_PLAY 0x58B # Was: play
KEY_FASTFORWARD 0x38B # Was: ff
KEY_RECORD 0xB8B # Was: rec
KEY_STOP 0xC4B # Was: stop
KEY_PAUSE 0x98B # Was: pause
end codes
end remote
